🚀 Looking for an alternative?
This Pyrodrone item is currently out of stock or discontinued. We highly recommend checking out our premium in-stock alternatives from top brands like T-Motor, GEPRC, and iFlight in the Flight Control & Power section!

It’s finally here!
The pyrodrone F4 board has been one of the very few boards with perfectly flat one side which lot of guys been utilizing as a “shelf” for their VTX and RX.
It was time to reroute the pads and offer a direct clean solder option for the TBS UNIFY V3 VTX and the TBS Nano RX similar to the Whitenoise Synergy FC.
The Pyro F4 RACE also has a built in socket which makes it plug & play with the Pyro32 F3 45A 4in1 ESC (The correct harness is ONLY included in the ESC package)

Please check below for tips and Betaflight Settings.

MPU6000 Gyro STM32F405 CPU @ 168mhz, can be overclocked
2-6S direct battery input
3.3V 100ma, 5V 2A BEC
5V and Vbat Camera Power
Built in configurable Betaflight OSD
Flat bottom PCB for SUPER CLEAN builds
36×36 PCB with 30.5×30.5 mounting holes
6 UARTS.
UART1 (INVERTER FOR SBUS),
UART2 (FREE),
UART3 (INVERTED TELEMETRY), use CLI command : Set tlm_halfduplex=off UART4 (Free),
UART5 (Smart Audio)
UART6 (Free)
The Pyrodrone F4 RACE flight controller can power HV VBAT or 5V Video transmitters.
BF Target: PYRODRONEF4

Please make sure to jump the correct selection for your VTX.

voltageselector ada62b86 fd25 4982 9260 58e778b841f6

If you want to use the VTX PIT mode function please type the following in the CLI command line:

resource pinio 1 A15 (Hit Enter)
Set pinio_box = 39 (Hit Enter)

Save (Hit Enter)
Assign a switch to the VTX PIT option in Betaflight MODES tab.

If VTX PIT mode is NOT needed then just solder your VTX and fly! (no additional settings needed)

If you want to solder the TBS UNIFY 5V direct to the board which is where this FC REALLY shines then here are couple tips for you.

Using the TBS Direct mount feature means you have to flip the board upside down with the USB to the left side of the drone.
SO REMEMBER to change the board orientation in Betaflight configuration tab.

orientation 755dec74 bf37 4430 97a3 8f3ae49c4363

Both the VTX and the board have “anchor” Pads on both sides of the VTX, but we do not recommend using all these anchor points for easier future maintanence in case you ever have to remove the VTX.
Here is what we recommend.
Use a very thin piece of the double sided tape that is provided in your TBS UNIFY V3 package and apply it on the VTX as shown in the below picture.
This will work as a place holder for you to line up and solder the 4 points.

When sticking the VTX to the board make sure the 4 points on the VTX (VID-AUD-GND-5V) line up with the 4 pads on the flight controller.
Once lined up solder the 4 points.

69644381 373653080232463 2390553843193610240 n grande

Now it’s time to solder your receiver.
The board is labled for TBS NANO RX as the holes perfectly line up with the Nano RX, but you can really use any RX and just choose the correct type of receiver in the Betaflight configuration page.
Our preferred way of mounting the RX is with silicone wires rather than direct solder, Again for easier future maintenence purposes.
Please check the below picture:

For correct voltage reading change the Voltage scale value to 160
If you charge your batteries over 4.20 per cell AKA HV then remember to adjust the Maximum Cell Voltage to 4.4 otherwise the average cell voltage will read wrong on your OSD.

MAECENAS IACULIS

Vestibulum curae torquent diam diam commodo parturient penatibus nunc dui adipiscing convallis bulum parturient suspendisse parturient a.Parturient in parturient scelerisque nibh lectus quam a natoque adipiscing a vestibulum hendrerit et pharetra fames nunc natoque dui.

ADIPISCING CONVALLIS BULUM

Vestibulum penatibus nunc dui adipiscing convallis bulum parturient suspendisse.
Abitur parturient praesent lectus quam a natoque adipiscing a vestibulum hendre.
Diam parturient dictumst parturient scelerisque nibh lectus.

Scelerisque adipiscing bibendum sem vestibulum et in a a a purus lectus faucibus lobortis tincidunt purus lectus nisl class eros.Condimentum a et ullamcorper dictumst mus et tristique elementum nam inceptos hac parturient scelerisque vestibulum amet elit ut volutpat.

-47% Sold out