Matek H7A3-Slim Flight Controller – 30x30mm

SKU: A3-13433

Small Parcel

15-30 Days

Free

Special Line

Our courier will deliver to the specified address

7-15 Days

From $20

Courier delivery

courier will deliver to the specified address

3-5 Days

From $40

$83.99

Out of stock

Out of stock

Don't Miss Top Accessories

Description

Packed with features, the H7A3-Slim from Matek is ready to go.

Check out all our 30x30mm Flight Controllers and the rest of our Matek Products!

 

H7A3 SLIM 1

H7A3 SLIM layout

H7A3 SLIM Wiring

can

Specifications:

  • MCU: STM32H7A3RIT6, 280MHz Cortex-M7, 1.4MB RAM, 2MB Flash
  • IMU: ICM42688P
  • Baro: SPL06-001
  • OSD: AT7456E
  • Blackbox: 128MB Flash (1G-bit NAND)
  • 6x Uarts (1,2,3,4, 5, 6) with built-in inversion.
  • 11x PWM outputs
  • 1x I2C
  • 1x CAN
  • 4x ADC (VBAT, Current, VB2, Cur2)
  • 3x LEDs for FC STATUS (Blue, Red) and 3.3V indicator(Red)
  • USB Type-C(USB2.0)
  • 8x PWM outputs on 2x JST-SH1.0_8pin connector for 2x 4in1 ESC
  • 1x JST-GH1.25_4pin connector (5V/CAN-H/CAN-L/G)
  • 9V output ON/OFF switchable
  • Digital video OSD is supported by any spare UART

        Power

        • Vbat Input: 6~36V (2~8S LiPo)
        • BEC: 5V 2A cont. (Max.3A)
        • BEC: 9V 2A cont. (Max.3A)
        • LDO 3.3V: Max.200mA
        • No Current Sensor built-in
        • ADC VB2 pad supports Max. 69V (voltage divider: 1K:20K)

        FC Firmware

        Physical

        • Mounting: 30.5 x 30.5mm, Φ4mm with Grommets Φ3mm
        • Dimensions: 36 x 36 x 5 mm
        • Weight: 7g
        • 3D step  H7A3-SLIM_step.zip

        ArduPilot Mapping:

        RC INPUT

        RC input is configured on the USART2(SERIAL2). It supports all serial RC protocols. SERIAL2_PROTOCOL=23 by default.

        • PPM is not supported.
        • CRSF requires Tx2 & Rx2 connection, and set SERIAL2_OPTIONS to “0” (default).
        • SBUS/DSM/SRXL connects to the Rx2 pin, but SBUS requires that the SERIAL2_OPTIONS be set to “3”.
        • FPort requires connection to Tx2, and set SERIAL2_OPTIONS to “7”. If Telemetry doesn’t work, try set  SERIAL7_OPTIONS = 135.
        • SRXL2 requires a connection to Tx2, and automatically provides telemetry. Set SERIAL2_OPTIONS to “4”.
        • Any UART can be used for RC system connections in ArduPilot also, and is compatible with all protocols except PPM. See Radio Control Systems for details.

        ArduPilot Relay(PINIO)

        • 9V output ON by default
        • PC13 PINIO1 OUTPUT GPIO(81)   //9V power switche.g.
        • RELAY_PIN       81    // PINIO1 GPIO
        • RC7_OPTION   28    //Relay On/Off, Use CH7 of Transmitter to set 9V ON/OFF

        The configured feature will be triggered when the auxiliary switch’s pwm value becomes higher than 1800. It will be deactivated when the value falls below 1200.

        Check the pwm value sent from the transmitter when the switch is high and low using the Mission Planner’s Initial Setup >> Mandatory Hardware >> Radio Calibration screen. If it does not climb higher than 1800 or lower than 1200, it is best to adjust the servo end points in the transmitter.

        Package Includes:

        • 1 x H7A3-SLIM
        • 6 x Silicon grommets M4 to M3
        • 2 x JST-SH1.0_8pin cable, 5cm,  & 8pin connectors
        • 1 x JST-GH-4P to JST-GH-4P cable for CAN port, 20cm

        Specification

        Overview

        Weight0.01 kg

        Customer Reviews

        Reviews

        There are no reviews yet.

        Only logged in customers who have purchased this product may leave a review.